TITLE
Quick Start Guide Access - Videos, Software, and Documents

SECTION
00:00:02 Introduction and Purpose

INSTRUCTION STEPS
1) Watch the full setup video series step by step to ensure proper installation and minimize downtime.
2) Pause or rewind videos as needed to follow instructions accurately.

SECTION
00:00:02 Locating the Quick Start Guide via USB

INSTRUCTION STEPS
1) Locate the USB drive included with your printer.
2) Insert the USB drive into your computer.
3) Open the Quick Start Guide PDF file stored on the USB.

SECTION
00:00:36 Alternative Access via Email

INSTRUCTION STEPS
1) If the USB drive is missing or its contents are unavailable, open the email from the dealer where the printer was purchased.
2) Locate the most up-to-date Quick Start Guide URL link provided in the email.
3) Double-click the Quick Start Guide PDF file from the link.

SECTION
00:00:36 Downloading and Saving the Quick Start Guide

INSTRUCTION STEPS
1) Open the Quick Start Guide PDF.
2) Click on Important Resources.
3) Download the Quick Start Guide PDF.
4) Save a copy of the PDF to your desktop.

SECTION
00:01:26 Using and Storing the Quick Start Guide

CHECKLIST
- One-page PDF format
- Contains QR codes
- Includes links to videos, software, and documents needed for setup
- Stored in an easily accessible location

SECTION
00:01:26 Next Steps

CHECKLIST
- Proceed to the next setup video

TITLE
Miro 13 Max Powder Shaker Oven - Installation Guide

SECTION
00:00:02 Tools and Unboxing Preparation

CHECKLIST
- Screwdriver
- Work gloves
- Blade

INSTRUCTION STEPS
1) Open the box using a blade.
2) Remove all items from inside the box.
3) Remove and set aside all styrofoam packaging.
4) Note that contents may change over time and contact DTF Station technicians if there are significant differences from the video.

SECTION
00:01:05 Initial Unit Preparation

INSTRUCTION STEPS
1) Open the powder station lid.
2) Remove the takeup reels and takeup reel brackets.
3) Close the powder station lid.
4) With at least two to three people, carefully lift and remove the unit from the box.
5) Locate the rods underneath the Miro 13 Max.
6) Remove protective films from all accessories.
7) Place the styrofoam back into the box and retain it for future use.
8) Retain all original packaging, including styrofoam, for warranty purposes for up to six months.
9) Take a photo of the serial number sticker.
10) Register the equipment on the Discord profile page using the serial number.

SECTION
00:01:48 Bracket Assembly

INSTRUCTION STEPS
1) Locate the two brackets shown in the video.
2) Find the knob screws in the Ziploc bag.
3) Connect the brackets using three knob screws on each side.

SECTION
00:03:34 Film Tension Rod Installation

INSTRUCTION STEPS
1) Locate the silver film tension rod.
2) Insert the rod into the brackets using two bearings and knob screws.
3) Insert the film alignment adjusting ring before locking the rod.
4) Insert the knob screws on both sides.
5) Adjust the rod until it is straight.
6) Tighten the knob screws securely.

SECTION
00:03:34 Takeup Reel Rod Installation

INSTRUCTION STEPS
1) Thread the two takeup reel rods into the brackets.
2) Partially loosen the knobs on the takeup reels.
3) Insert the takeup reels into the rods.
4) Loosen the knobs on the brackets to center the rods.
5) Once centered, tighten all knobs.
6) Spread out the takeup reels.
7) Insert the paper core onto the takeup reel.
8) Center the paper core.
9) Tighten the knob screw to secure the paper core.

SECTION
00:04:59 Takeup Motor Connection

INSTRUCTION STEPS
1) Connect the takeup motor connector to the Miro 13 Max body.
2) Ensure the connector is fully and properly seated.

SECTION
00:04:59 Media Wheel Assembly

INSTRUCTION STEPS
1) Locate the media wheel components.
2) Loosen the screws to insert the rods.
3) Partially lock the rods in place.
4) Do not overtighten to avoid bending the rods.
5) Open the powder station lid.
6) Place the media wheel into the groove inside the powder station.

SECTION
00:05:39 Power Connection and Initial Power-On

INSTRUCTION STEPS
1) Locate the power cord.
2) Plug the power cord into the unit.
3) Plug the other end into a power source using a power strip to prevent sudden power loss.
4) Turn on the main power.
5) Verify that the display turns on.

SECTION
00:06:04 Functional Testing

INSTRUCTION STEPS
1) Turn on the preheating button.
2) Wait approximately 5 minutes.
3) Verify the preheating platen is warming up.
4) Turn on the purifier.
5) Confirm the purifier fan is running.
6) Turn on the shaking power.
7) Adjust the shaking speed intensity control knob to increase or decrease paddle speed.
8) Turn on the takeup reel power.
9) Verify the takeup motor runs when the media wheel is engaged.

SECTION
00:06:36 Temperature Settings and Film Notes

INSTRUCTION STEPS
1) Press the reset button to set default temperatures.

CHECKLIST
- Main heating plate default temperature: 130 C
- Preheating plate temperature range: 50 to 80 C
- Color Prime Universal Film: warm peel film
- Color Prime Quick Glide Film: hot peel film

CHECKLIST
- Refer to the operation video for correct film settings
- Contact a DTF Station technician if assistance is needed

SECTION
00:07:09 Shutdown and Table Installation

INSTRUCTION STEPS
1) Turn off the main power.
2) Unplug the power cord.
3) Allow the unit to cool for several minutes.
4) Move the unit onto the Print Pro table.
5) Position the wheels with brakes facing outward to align with the table slots.
6) Engage the brakes on all four wheels.

CHECKLIST
- Print Pro table is sold separately
- Contact a local distributor to purchase the table
- Refer to the Print Pro table installation video for table setup